How to Remove Blink Doorbell

You’re up on a small step stool, screwdriver in hand, staring at your Blink doorbell like it’s a puzzle you didn’t sign up for. Maybe you’re switching to a new device. Maybe you’re repainting the porch. Maybe the doorbell keeps dropping its Wi-Fi and you want to reset it fresh.

You give it a wiggle. It won’t budge. You pull harder, and now you’re worried about snapping a clip or yanking a wire loose.

Take a breath.

Removing a Blink doorbell is simple once you know the trick — and there is a trick. In this guide, you’ll learn how to remove a Blink doorbell step by step, whether it’s battery-powered or wired to your chime. You’ll find the right tool to use, how to avoid electrical mistakes, and how to fix the snags that trip most people up. Let’s get it off the wall the safe way.

Why the Right Method Matters

Most people try to pry the doorbell straight off the wall first. That’s the mistake.

Here’s the thing: your Blink doorbell isn’t glued or screwed to the wall directly. It clips onto a mounting bracket, and that bracket is what’s fastened to your porch. The doorbell releases with a small removal tool — a thin metal pin that pops the clip loose.

Force it without that pin, and you risk cracking the housing or bending the bracket.

There’s a second layer too. If your doorbell is wired to an existing chime, live voltage runs to it. Pull it off carelessly and you can short the wires or trip a breaker.

So the order matters. Here’s the safe sequence:

1. Figure out your setup — battery-only or wired.
2. Kill the power if it’s wired.
3. Release the doorbell from its bracket with the removal tool.
4. Disconnect any wires and unscrew the bracket if you’re taking it down for good.

In short: your Blink doorbell clips onto a bracket, so use the release pin — never brute force.

What You’ll Need Before You Start

Good removal comes down to two things: the right tool and a little patience. You won’t need much.

Gather these before you climb up:

• The Blink removal tool (the small metal pin that came in the box)
• A paperclip or SIM-eject pin as a backup if you lost the tool
• A Phillips screwdriver for the mounting bracket screws
• A voltage tester if your doorbell is wired
• Painter’s tape to label wires so you don’t mix them up
• A soft cloth to protect the wall and catch dropped screws
• The Blink Home Monitor app to remove the device from your account

Warning: If your doorbell is wired to your home’s chime, turn off the power at the breaker box before you touch any wires. Skipping this step risks a shock or a blown fuse.

Charge your phone and update the Blink app. You’ll use it to delete the device so you don’t get “camera offline” alerts later.

In short: the release pin, a screwdriver, and the app are the three things you’ll reach for most.

How to Remove a Blink Doorbell Step by Step

Let’s get into the actual removal. The core steps stay the same, with one extra step if yours is wired.

Step 1: Delete the Device in the App (Optional but Smart)

If you’re removing the doorbell for good, take it out of your account first.

1. Open the Blink Home Monitor app.
2. Tap your doorbell on the home screen.
3. Go to Device Settings (the gear icon).
4. Scroll down and tap Delete Device.
5. Confirm.

This stops the endless offline notifications once the doorbell loses power.

Step 2: Cut the Power (Wired Setups Only)

Skip this if your Blink doorbell runs on AA lithium batteries alone.

If it’s wired to your chime:

1. Go to your breaker box.
2. Flip the breaker labeled for your doorbell or front entry.
3. Back at the door, press the doorbell button to confirm it’s dead.
4. Use a voltage tester on the wires once the doorbell is off, just to be sure.

Never rely on the label alone — old panels are often mislabeled. Test to be safe.

Step 3: Release the Doorbell From the Bracket

This is the part people struggle with, and it’s actually the easiest once you know how.

1. Find the small hole at the bottom edge of the doorbell.
2. Insert the Blink removal tool (or a straightened paperclip) into that hole.
3. Press firmly and straight in until you feel a click.
4. Tilt the top of the doorbell away from the wall as you press.
5. The doorbell lifts off the bracket.

Don’t pry from the sides. The release only works from that bottom pinhole.

Step 4: Disconnect the Wires (Wired Setups Only)

With the doorbell off the bracket, you’ll see two small wires on the back if it’s wired.

1. Label each wire with painter’s tape (left and right).
2. Loosen the terminal screws on the back of the doorbell.
3. Slide the wires free gently.
4. Tape the wire ends to the wall so they don’t slip into the hole.

Step 5: Remove the Mounting Bracket

Taking the whole thing down? Remove the bracket too.

1. Unscrew the bracket from the wall with your Phillips screwdriver.
2. Keep the screws in case you remount later.
3. Fill the holes with a bit of putty if you’re done for good.

In short: delete in the app, cut power if wired, pop the release pin, then handle wires and bracket.

Battery vs. Wired: Which Removal Applies to You?

Not sure which path is yours? This table breaks it down fast.

Feature	Battery-Only Blink Doorbell	Wired Blink Doorbell	Best For
Power source	Two AA lithium batteries	Home chime wiring (16–24V)	Renters vs. homeowners
Power-off step	Not needed	Required at breaker	Safety-first users
Removal tool	Release pin only	Release pin + screwdriver	Everyone
Wire handling	None	Label and disconnect	Wired installs
Time to remove	2–3 minutes	8–10 minutes	Quick vs. careful jobs
Difficulty	Very easy	Medium	First-timers

If you never touched your breaker during setup, you’re almost certainly on battery power. If you connected wires to a chime, you’re wired — and that breaker step is not optional.

In short: battery removal is a two-minute job, while wired removal needs the power off first.

How to Handle Adhesive or No-Drill Mounts

Some people skip screws and mount the bracket with adhesive strips or a no-drill plate. Removing these takes a slightly different touch.

Adhesive-Mounted Brackets

If your bracket sits on double-sided tape or a 3M strip:

1. Release the doorbell from the bracket first, as usual.
2. Warm the adhesive with a hair dryer on low for about 30 seconds.
3. Slide dental floss behind the bracket in a sawing motion.
4. Peel the bracket away at a low angle.
5. Wipe leftover residue with a little rubbing alcohol.

Warm adhesive releases with almost no force. Cold adhesive fights back and can lift your paint.

No-Drill Mounting Plates

Some third-party plates clip or slide off a base.

• Check for a release tab at the top or bottom edge.
• Slide the plate upward if it uses a keyhole slot.
• Look underneath for hidden screws before pulling hard.

In short: pop the doorbell off first, then warm and peel adhesive gently to protect your wall.

Common Mistakes and Troubleshooting

This is where a quick job turns into a cracked doorbell or a tripped breaker. Here are the slip-ups people make when they remove a Blink doorbell — and how to fix each one.

Mistake 1: Prying the Doorbell Instead of Using the Pin

Why it happens: The doorbell feels stuck, so people grab the edges and pull.

The cost: You crack the plastic housing or snap the internal clip. Now the doorbell won’t sit right even if you remount it.

The fix: Use the removal tool in the bottom pinhole. Press straight in until it clicks, then tilt the top away. No prying needed.

Mistake 2: Forgetting to Cut the Power on Wired Units

Why it happens: The doorbell looks harmless, so people assume it’s safe to touch.

The cost: Doorbell wiring carries live low voltage. Touch both wires at once and you can short the transformer, trip a breaker, or get a startling zap.

The fix: Flip the breaker first, then press the button to confirm it’s dead. Test the wires with a voltage tester before you loosen anything.

Mistake 3: Losing the Removal Tool

Why it happens: That tiny metal pin is easy to toss out with the packaging.

The cost: You’re stuck with the doorbell on the wall and no obvious way off.

The fix: A straightened paperclip or a SIM-eject pin works just as well. Both fit the release hole and pop the clip.

Mistake 4: Not Labeling the Wires

Why it happens: There are only two wires, so people figure they’ll remember.

The cost: If you ever reconnect them backward, your doorbell may not power on or your chime may buzz oddly.

The fix: Slap a piece of painter’s tape on each wire before you disconnect. Mark them left and right. It takes ten seconds and saves real frustration.

Mistake 5: Skipping the App Deletion

Why it happens: Once the doorbell is off the wall, people think they’re done.

The cost: The app keeps pinging you with “device offline” alerts, and the doorbell stays linked to your account. That’s a headache if you sell it or gift it.

The fix: Delete the device in the Blink Home Monitor app under Device Settings. This clears it cleanly and lets a new owner set it up fresh.

Mistake 6: Ripping Adhesive Mounts Cold

Why it happens: People treat adhesive brackets like they’d treat a sticker — just yank.

The cost: A cold pull rips paint and lifts drywall paper, leaving a patch job behind.

The fix: Warm the adhesive with a hair dryer, then slide floss behind it and peel at a shallow angle. Slow and warm beats fast and cold every time.

In short: use the release pin, cut power on wired units, keep a paperclip handy, label your wires, and delete the device in the app.

Frequently Asked Questions

How do I remove a Blink doorbell from the wall?

Find the small hole at the bottom of the doorbell and insert the Blink removal tool or a straightened paperclip. Press firmly and straight in until you feel a click, then tilt the top of the doorbell away from the wall. It lifts right off the mounting bracket.

Do I need a special tool to remove my Blink doorbell?

Not really. Blink includes a removal pin in the box, but a paperclip or SIM-eject tool does the exact same job. Any thin, sturdy pin that fits the bottom release hole will pop the clip loose.

Will removing my Blink doorbell delete my recordings?

No. Your clips are stored in the cloud or on your Sync Module, not on the doorbell itself. Removing the doorbell from the wall or even deleting it from the app won’t erase footage you’ve already saved.

How do I take down a wired Blink doorbell safely?

Turn off the power at your breaker box first, then press the doorbell button to confirm it’s dead. Release the doorbell with the pin, label the two wires, and unscrew them from the terminals. Always test the wires with a voltage tester before touching them.

Can I reuse my Blink doorbell after removing it?

Absolutely. The doorbell stays fully functional once it’s off the wall. Just delete it from your old account in the app, then set it up again like new at its next spot — the fresh setup takes only a few minutes.

Wrapping Up

Taking down a Blink doorbell doesn’t have to mean cracked plastic or a tripped breaker.

Here’s what to hold onto. Delete the device in the app, cut the power if your doorbell is wired, then pop the release pin into that bottom pinhole and tilt the doorbell free. Label your wires, unscrew the bracket if you’re done, and warm any adhesive before you peel it. That order protects your device, your wiring, and your porch wall.

You’ve got this — battery or wired, it comes off cleanly when you take it slow.

Ready to set things back up? Check out our guide on [related topic: reinstalling and repositioning your Blink doorbell for the best coverage].